Buy NanoStation M2 for an IP camera: the second Ethernet port and power supply
Request the NanoStation M2 for the camera platform
At a remote warehouse or entrance, the camera and radio may be nearby. The buyer wants to transfer the image to the existing network and understand in advance whether an additional switch or a separate power supply is needed. For NanoStation M2 It is useful to separate these issues: connecting data to another port and power supply cameras have different conditions. A suitable kit is determined by the specific camera offered by NSM2 and the connection project.
What is described for the second port
In Manufacturer's manual NanoStationM/locoM The secondary Ethernet port for NanoStation M2 is described as a bridge port, with software-configurable PoE pass-through. To use this power supply transmission, the document specifies a 24V, 1A adapter. This information relates to the described equipment; it does not establish electrical compatibility with an arbitrary camera.
Therefore, the subject of the request is the connection of a particular camera and the agreed method of its power supply. Don’t consider PoE pass-through as a promise of universal power supply to any standard, including 802.3af/at. Compare the requirements of the camera, the proposed device and the source according to their documentation. If the power supply of the camera is organized separately, specify this as part of the saved solution.
First, decide where the image should go.
Write a full camera model, installation location and model of the recorder or video surveillance server. Find out what equipment is already on the other side of the connection. Note what you need to get: access to the image, transfer to record, camera maintenance, or several of these tasks. The word “connect” without a result leaves a substantial part of the order uncertain.
If the camera is already running through an existing switch, indicate its role and the reason for the change. Perhaps you buy only a radio device, and the wired part remains. If the new scheme should reduce the number of individual nodes, ask to show the full proposed composition and check the necessary actions. The ability to remove the device from the estimate is determined by the project, not by the number of connectors on the body.
| Part of the solution | What to indicate in the request |
|---|---|
| Camera. | Complete model, required data and power supply method |
| NanoStation M2 | Precise configuration, condition and necessary preparation |
| The remote side | Operating radio device and network connection |
| Video recipient | Registrar or server and desired access result |
| Preservation of equipment | Switch, Camera Source and Existing Connections |
Data and Power Supply – Separate Lines of the Package
The option “data through the second port, power supply camera separately” and the option with coordinated transmission power supply have different composition. In the second, it is necessary to determine a suitable source for the described chain and confirm the applicability to the camera itself. Software configuration is included in the quotation for a specific configuration NSM2; one photo of the interface of another apparatus does not replace such verification.
A source that is agreed to power supply only by NanoStation cannot automatically be considered a source for the entire new chain. Attach markings of existing blocks and designation of the applicable camera instruction. If a new adapter, separate injector, or other accessory is required, each confirmed component must have its own string. The familiar form of an Ethernet connector does not close off the choice of electrical connection.
What to ask to show before receiving the kit
The verification shall follow the agreed scheme. For hardware delivery, this can be identification and completeness; for the prepared solution, it can also be the connection of the described camera and the verification of data transmission. Determine in advance who provides the camera, remote equipment and access to the test network. Don’t replace the entire chain check with a demonstration of one on. NSM2.
| Acceptance scenario | Agreed outcome |
|---|---|
| Connecting the selected camera | Required recipient sees the image according to the accepted scheme |
| Transfer on record | The designated registrar or server receives the desired stream. |
| Selected Power Supply Camera | Composition and applicability confirmed by documents and agreed verification |
| Maintenance of equipment | Responsible Specialist Gets Project Access |
Specify the normal workload and the conditions for checking the video. The number of cameras, image settings, and latency requirements are your source data. NanoStation M2 cannot be assigned a guaranteed number of video streams or the result of a radio connection. The result of the quotation should explain which equipment is being tested and against which agreed criteria.
Make a purchase for the object
The main position is NanoStation M2 with agreed accessories and training. Canopy 5200APG and 5250SMBC They are on a different platform; their cards are useful if the enterprise is separately discussing the existing Canopy site. They are not an automatically compatible second party for NSM2, nor do they determine the power supply of the camera.
To receive in Novosibirsk, St. Petersburg, Karaganda or Astana, specify the country, the exact address and the receiving specialist. Attach the camera model, the proposed scheme, the saved parts and the desired date. The historical list contains the NanoStation M2; the current availability, condition, composition and conditions of receipt are confirmed in the current KP.
Questions before buying
Does the second port automatically power any IP camera?
The applicability of power supply transmission is checked against camera documentation, specific NSM2 and source. Ethernet port does not establish universal power supply compatibility.
Can I keep a separate camera source?
This option can be included in the draft. The quotation separates the data connection, the stored power supply and the necessary additional accessories.
What do you need for a useful quotation for NSM2?
Full camera model, remote-side equipment, assigned registrar or server, power supply method and expected verification results.
Equipment cards
NanoStation M2
The main subject of the article; the proposed configuration and preparation are consistent.
Open the product card
Canopy 5250SMBC
Canopy's own project position; compatibility is not established by the card neighborhood.
Open the product cardNanoStation M2 is the main item of purchase · 5200APG - a separate node of the Canopy network · 5250SMBC – Canopy’s Subscriber Position.